ASTM D1121-11(R2020) pdf free download

ASTM D1121-11(R2020) pdf free download.Standard Test Method for Reserve Alkalinity of Engine Coolants and Antirusts
1. Scope
1.1 This test method covers the determination of the reserve alkalinity of new, unused engine coolants, and liquid antirusts as received, of used or unused aqueous dilutions of the concentrated materials, and of aqueous dilutions of solid antirusts. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appro- priate safety, health, and environmental practices and deter- mine the applicability ofregulatory limitations prior to use. 1.4 This international standard was developed in accor- dance with internationally recognized principles on standard- ization established in the Decision on Principles for the Development of International Standards, Guides and Recom- mendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
4. Summary of Test Method
4.1 A 10 mL sample of concentrated coolant, antirust, coolant additive, or an aqueous engine coolant containing these products, is diluted to about 100 mL with water and titrated potentiometrically with 0.100 N hydrochloric acid to a pH of 5.5. The volume of acid used is reported to the nearest 0.1 mL. The concentration ofcoolant or additive in the coolant solution shall be recorded if required, for calculation of depletion of the reserve alkalinity during performance tests.
5. Significance and Use
5.1 Reserve alkalinity is the number of millilitres, to the nearest 0.1 mL of0.100 Nhydrochloric acid (HCl) required for the titration to a pH of 5.5 of a 10 mL sample of an undiluted, unused coolant, antirust, or coolant additive, and unused or used solutions thereof. 5.2 Reserve alkalinity is a term applied to engine coolants and antirusts to indicate the amount of alkaline components present in the product. It is frequently used for quality control during production, and values are often listed in specifications. When applied to used solutions, reserve alkalinity gives an approximate indication of the amount of remaining alkaline components. Unfortunately, the term is sometimes misused in that its numerical value is said to be directly related to coolant quality, the higher the number, the better the coolant. ASTM Committee D15 on Engine Coolants believes there is a need to correct some misconceptions and place the term in its proper perspective. 5.3 Reserve alkalinity (R.A.) as defined in Section 3 of this method is the number of millilitres of 0.1 N hydrochloric acid required to titrate 10 mL ofconcentrated coolant to a pH of5.5. The term is not a completely accurate description of the property being measured because “alkalinity” usually refers to the pH range above 7.0. 5.4 A review of the origin of the term may be helpful in attempting to understand its proper use. When ethylene glycol was first used as an engine coolant, it was uninhibited. The need for inhibition soon became apparent and triethanolamine was incorporated. When solutions of this inhibited glycol were titrated with dilute hydrochloric acid, it was found that the steepest part of the neutralization curve occurred at a pH of about 5.0. Following the introduction of triethanolamine, other buffers, such as borates and phosphates, have been used. Titration to 5.5 was employed with these buffers which have an end point close to 5.5. 5.5 Generally, most metals in an automotive cooling system corrode less in solutions which are mildly alkaline. The commonly used alkaline buffers, borates and phosphates, help to maintain this desirable alkalinity and a stable pH for substantial additions of acid. A well inhibited coolant contains smaller amounts of other inhibitors (in addition to the buffers), to give broad range corrosion protection for all of the metals found in the cooling system. These additional inhibitors may contribute very little to the titration, but they can provide excellent corrosion protection. 5.6 The alkaline inhibitors provide buffering action and neutralize acids introduced into the coolant by exhaust gas leakage, by residual acid cleaner, or by the oxidation of ethylene glycol and propylene glycol. Some inhibitors which contribute little or no reserve alkalinity may give excellent corrosion protection to certain metals but have little capacity to combat acid contamination. In view of this, the magnitude of the R.A. in a coolant is not always a good criterion in determining its potential protective properties.